The Ultimate ELYARCHI Unboxing Guide: 3-Step Setup for a Perfect First Print in Under 1 Hour

In News 0 comment
The Ultimate ELYARCHI Unboxing Guide: 3-Step Setup for a Perfect First Print in Under 1 Hour

Unboxing a new 3D printer is exciting, but the setup can seem daunting. Worried about complicated instructions and a pile of parts?

Don't be! This simple ELYARCHI 3D printer unboxing guide breaks down the entire process into just 3 core steps. Even if you're a complete beginner, you can be ready for your first print in under an hour!

Pre-Setup: Prepare Your Workspace

Before you start, ensure you have a wide, flat, and stable surface (like a desk or table). Have these items ready:

  • The included accessory box

  • A pair of gloves (to avoid fingerprints on the build plate)

  • A can-do attitude!

Step 1: Build the Foundation → Assembly & Bed Leveling

This is the most critical step for print success. Thankfully, ELYARCHI has made it incredibly simple.

1. Unbox & Inventory:
Carefully unbox and you should find:

  • The partially assembled main unit

  • A tool kit (typically includes hex keys, spatula, screws)

  • Power cable

  • Spool holder

  • A small sample spool of PLA filament

  • A USB drive or SD card (with test models)

2. Attach the Spool Holder & Screen:

  • Snap the spool holder into the designated slots on top of the printer until you hear a "click."

  • Adjust the hinged touchscreen to your preferred viewing angle.

3. The Core Step: Automatic Bed Leveling!

  • On the touchscreen, find and select the "Auto Bed Leveling" or "Auto Home" function.

  • The printer will now automatically probe multiple points across the print bed. Do not touch the printer during this process.

  • After about 5 minutes, the process completes. The printer saves the mesh data to ensure a perfect first layer.

Pro-Tip for Beginners: Ensure the build plate is clean and free of grease. The probing noise is normal!

Step 2: Connect & Prepare → Load Filament & Pre-heat

The foundation is set. Now, let's "feed" and "warm up" the printer.

1. Load the Filament:

  • Place the sample PLA spool on the holder.

  • Cut the end of the filament at a sharp angle.

  • On the touchscreen, select "Load Filament" or "Preheat PLA". The hotend will begin heating.

  • Once it reaches the target temperature (around 200°C), gently insert the filament into the feed tube. You will feel the extruder gears grip it and see a small amount of molten plastic extrude from the nozzle.

2. Prepare the Build Plate:

  • ELYARCHI usually comes with a flexible spring steel plate. Before your first print, thoroughly wipe the build surface with the included isopropyl alcohol wipe to remove any oils. This is the secret to preventing prints from warping!

Pro-Tip for Beginners: Guide the filament gently—don't force it. If you meet resistance, retract it slightly and try again.

Step 3: One-Click Print → Start Your First Model

Everything is ready! Let's print a classic test model.

1. Slicing? Not Yet! Use the Test Model.

  • For your very first print, skip the slicer software entirely. Use the pre-loaded test model on the provided USB drive/SD card (often a "benchy," cube, or calibration cat).

  • On the touchscreen, select "Print" and navigate to this file.

2. Start Printing & Observe:

  • Hit print! The print head will move and begin drawing a purge line along the edge of the plate to clean the nozzle and ensure smooth flow.

  • Watch the First Layer: This is the golden rule of 3D printing. You should see the filament being smoothly "squished" onto the build plate, with lines that are connected and flat, without gaps or blobs.

3. You're Done!

  • Now, the printer will work automatically. You can sit back, relax, and watch the magic happen. In 20-40 minutes, your first 3D model will be complete!

Pro-Tip for Beginners: A good first layer means a 99% successful print. If it looks perfect, you're golden.

Recap: Your 1-Hour Setup Journey

Congratulations! You are no longer a 3D printing novice. Let's recap your quick and easy journey:

Step 1 (15 mins): Hardware Assembly + Auto Leveling — Build a solid foundation.
Step 2 (10 mins): Load Filament + Clean Plate — Prepare for success.
Step 3 (35 mins): Select Test File + Start Print — Enjoy the creation.

The ELYARCHI's design is focused on simplifying the beginner experience, with automatic bed leveling eliminating the most frustrating part of traditional printer setup.

Now, enjoy the thrill of your first 3D print! The feeling of holding that first successful model is unbeatable. Your next step is to explore slicer software like Orca Slicer to unlock infinite creative possibilities.

Happy Printing!

, ,